STATIC SCREEN SEPARATOR,
Alardsieve 24x36 hydrosieve screen,
all stainless steel...

A new Alardsieve 2436 water recovery screener / scalper hydrasieve screener, for food grade solids separation, wash-water filtration, and/or waste-water recovery. A Hydrasive type static screen sieve for separating solids from water and/or other liquids such as cooking oils.

This stationary screen is configured with a special triangular-rod / wedge-wire screen specifically designed for liquid-solid separation screening, with very precise and consistent sieve opening sizes. Product / solids in a liquid such as water or oil pass over the stationary screen. The liquid passes through the screen to a collection tank and drain, leaving the solids to pass over the screen for collection beneath.

An ideal static sieve screener-separator for wash-water reclaim / reuse, by-product recovery, and / or otherwise removing solids from waste water in industrial food processing plant applications such as peeling, coring, and grading operations for removing stems, seeds, leaves, and other foreign materials from rinse water. Also commonly used in other municipal and plant waste-water treatment facilities for solids removal filtration.

FEATURES:

• 24 inch wide by 36 inch long (top to bottom) static wedge-wire screen.
  
  
• .040 inch sieve-opening-size screen installed; --other standard sieve opening sizes can be sourced and installed to order, from .010 inch to .100 inch, with other sizes to be priced upon request. CALL 315-589-4511 to tell us YOUR sieve size specification.
  
  
• Screens are slide-out / slide-in interchangeable for a wide range of solids separation applications.
  
  
• 33 inch deep full-width infeed / head tank, tapering from 20 inches front-to-back at the top to 15 inches front to back at the bottom. The headbox is open and easily cleaned of debris such as stones or other such "heavies".
  
  
• Complete with dispersion shield over the weir to spread water evenly across entire screen, for optimal laminar flow.
  
  
• 4 inch threaded inlet, 6 inch threaded outlet; --allows for optional flange fittings to be screwed on, or for hose fittings to be cinched on to infeed and discharge connections.
  
  
• 4 inch diameter clean-out ports on either side (for easy access behind screen), with 1 inch tank drains at bottom level for comprehensive rinsing, cleaning and drainage of wash water.
  
  
• 1.25 inch diameter cleanout drain in each tank.
  
  
• Throughput capacity depends on screen sieve opening chosen. For example, with a .040 inch (1mm) sieve opening, a throughput capacity of approximately 400 gallons per minute capacity is feasible running non-greasy solids (actual throughput will depend on solids and flow characteristics).
  
  
• All food grade 304 stainless steel construction.
  
  
• Static screen / stationary screen water recovery sieve has no moving parts, making it a low cost, low maintenance and long-lived dewatering system.
  
  

As of this writing, this food grade solids separation / static dewatering screen is new, in stock at Alard, and available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your liquid solid separation equipment needs.

Alard item reference #: Y5858

TWO LANE
FLAT-TOP CONVEYOR,
table-top chain conveyor,
L-shaped, 90 degree turn,
all stainless steel...

An ARROWHEAD food grade stainless-steel-body TABLETOP CONVEYOR with dual 7.5 inch wide Delrin chain lanes and 90 degree left- angle turn.

FEATURING:

• Dual 7.5 inch wide plastic table top belts run side by side for a total belt width of 15.5 inches.
  
  
• L-shaped with 90 degree turn:
  
  
  • 96 inch long infeed.
    
    
  • 189 inch long discharge.
    
    
  • 44 inch working height with stainless steel legs & adjustable foot pads.
    
    
  • Rail supports on sides (rails not included).
    
    
  • 2 HP drive motor.
    
    
  • 3 phase electrical input.

As of this writing, this left-angle turn conveyor is in stock at ALARD, in GOOD condition, available for timely shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food processing transfer caonveyor equipment needs.

ALARD item reference #: Y3744

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 14x6 opening,
food grade, stainless steel...

A refurbished FORTRESS BSH metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 5 7/8 inch high by 14 inch wide USABLE aperture.
  
  
• Stainless steel detection head with new epoxy liner.
  
  
• Digital operator control panel.
  
  
• NEW stainless steel conveyor frame.
  
  
  • 11.75 inch wide by 87 inch long plastic interlocking chain belt:
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 34 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Fortress metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process food safety product inspection needs.

ALARD item reference #: Y5725

Safeline
FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 26x8 opening,
food grade, stainless steel...
 

A refurbished SAFELINE metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 8 inch high by 25.5 inch wide USABLE aperture.
  
  
• Stainless steel detection head with two (2) frequencies, providing versatile adjustability for both wet and dry applications.
  
  
• Digital operator control panel.
  
  
• New stainless steel conveyor frame.
  
  
  • 25.5 inch wide by 87 inch long plastic interlocking chain belt.
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 32 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction.
  
  
• Belt stop alarm reject.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Safeline metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process food safety product inspection needs.

ALARD item reference #: Y5726

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 20x8 opening,
food grade, stainless steel...

A refurbished FORTRESS Phantom metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 8 inch high by 20 inch wide USABLE aperture.
  
  
• Stainless steel detection head with new epoxy liner.
  
  
• Digital operator control panel.
  
  
• NEW stainless steel conveyor frame.
  
  
  • 18 inch wide by 84 inch long plastic interlocking chain belt:
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 32 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Fortress metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food safety product inspection needs.

ALARD item reference #: Y5562

VIBRATING FEEDER,
vibratory shaker-feeder,
food grade, all stainless steel...

Key Iso-Flo vibratory conveyor for even-feeding to downstream equipment, such as a radial combination scale, cutting machine, filling machine, peeling machine or whatever food processing or packaging equipment.

FEATURES:

• Vibrating conveyor bed measuring 91.5 inch overall length by 18 inch wide.
  
  
  • Smooth flat stainless steel contact surfaces.
    
    
  • 6 inch high sidewalls.
    
    
  • Half-moon shaped discharge.
    
    
• Mounted on stainless steel legs with isolation springs. Can also be mounted from overhead, e.g. suspended from the ceiling, such as for feeding a radial combination scale. Call 315-589-4511 to discuss your particular bulk food product conveying and feeding requirements.
  
  
• Approximately 30 inch infeed height, 24 inch high discharge.
  
  
• All food grade sanitary stainless steel construction.
  
  
• New style Key Iso-Flo eccentric drive.
  
  
• 1 HP belt drive motor with adjustable pulleys to increase/decrease shake.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this vibrating shaker-feeder is in stock at ALARD, in EXCELLENT operational, mechanical, electrical, and cosmetic condition; available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial food process bulk food conveying / feeding needs.

ALARD item reference #: Y5035

52 gallon steam-jacketed pressure TANK, food grade, stainless steel...

A BOWA GmbH 200 LITER (52 gallon) steam jacketed pressure vessel, food grade, stainless steel, vertical TANK, with dome top and dish bottom.

FEATURES:

• 31 inch diameter by 55.5 inch deep jacketed vessel.
  
  
• 25 liter (6.6 gallon) jacket - CE certified.
  
  
• Dome top:
  
  
  • Lugged center cover with rubber seal.
    
    
  • 2.5 inch and 3.5 inch Tri-clamp inlet ports.
    
    
• Dished bottom with 1.5 inch center bottom outlet with manual valve and Tri-clamp connection for 7 inch high discharge.
  
  
• Jacket and internal pressure tagged for 58 psi.
  
  
• Air inlet, pop off valve and psi gauge.
  
  
• All food grade sanitary stainless steel construction.

As of this writing, this jacketed pressure tank is in-stock at ALARD, in VERY GOOD condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your food processing needs.

ALARD item reference #: Y3786

SIX ROLL continuous
PEELER-WASHER-SCRUBBER
for fruits and vegetables,
hydraulic powered, stainless steel,
for abrasive peeling
or as a brush washer...

A Magnuson Model WSP-2066 hydraulic driven 6-roll continuous abrasive peeler, brush washer, scrubber for fruits and vegetables, especially root crops such as potatoes, carrots, beets, cassava, radishes and other similar products in the context of industrial food processing and pre-cut packing line operations.
 

FEATURES:

• Currently configured with three (3) brush rolls and three (3) abrasive rolls - can be set with any combination of abrasive and/or brush rolls, with a range of grit and/or brush options for more or less peeling action.
  
  
• Peeling / Scrubbing rolls are powered by a 10 HP self-contained hydraulic power pack.
  
  
• 18 inch by 12 inch top hopper inlet opening on the hinged stainless steel cover at a 73 inch infeed height.
  
  
• Lubricating and rinsing action are provided in the chamber via a water spray header with spray nozzles.
  
  
• Retention time is controlled by a manually adjustable discharge gate at 48 inches high.
  
  
• Water, peels and debris drop to a full-length sloped water catch pan with a 6 inch center bottom outlet.
  
  
• Locking 7.5 inch locking casters for added mobility.
  
  
• All food grade sanitary stainless steel body.
  
  
• 460 volt 3 phase electrical input.

As of this writing, this six roll peeler is in stock at ALARD, available for timely service and shipment.

CALL 315-589-4511 to confirm availability and discuss your particular fruit and / or vegetable peeling and washing equipment needs.

ALARD item reference #: Y4528

CENTRIFUGAL PUMP,
2 inch inlet, 1.5 inch outlet,
with 1 HP MOTOR,
food grade, stainless steel...

An SPX/APV Model 4V2 stainless steel body centrifugal pump designed for small flow capacity with minimum head pressure for a multitude of fluid handling applications ranging from food products, washing, rinsing, recirculation, irrigation, general industrial & municipal use.

FEATURING:

• Manufacturer rated for 85 gallons per minute at 33 feet of head - pump curves available upon request.
  
  
• 5 7/8 inch diameter 4-blade impeller.
  
  
• 2 inch diameter inlet / 1.5 inch diameter outlet with Tri-clamp fittings.
  
  
• Food grade sanitary stainless steel pump.
  
  
• 1 HP 1740 rpm direct drive motor.
  
  
• 208/230/460 volt 3 phase electrical input.
  
  

As of this writing, this centrifugal pump is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular industrial food process pump and bulk material handling needs.

ALARD item reference #: Y5847

VOLUMETRIC AUGER FEEDER
with HOPPER,
1.75 inch diameter feed tube,
bulk solids metering feeder,
food grade, stainless steel...

A Schenck AccuRate "Tuf-Flex" mass flow hopper, dry ingredient feeder, is designed to handle virtually any dry material, including fine powders, granules, flakes, fibers, dry coatings, spices, seasonings, chips & pellets, without packing or bridging. The product feed hopper features a flexible vinyl chamber which is externally massaged for continuous even flow of uniform material. AccuRate Volumetric Series Feeders are manufacturer rated for industrial process applications including food, pharmaceutical, chemical, plastics and more.

FEATURING:

• Manufacturer rated for +/- 0.5% to 3.0% accuracy - depending on materials & flow rate.
  
  
• 17 inch square by 21 inch deep tapered stainless steel hopper.
  
  
  • Flexible vinyl feed chamber with external thumpers.
    
    
  • Solid stainless steel cover with 5.75 inch diameter infeed.
    
    
  • Safety pour grid.
    
    
  • 1.75 inch diameter by 25 inch long auger screw.
    
    
• 39 inch high infeed, 4 inch discharge height.
  
  
• Two (2) 3/4 HP washdown motors.
  
  
• 208/230/460 volt 3 phase electrical input.
  
  

As of this writing, this volumetric feeder is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition and available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial food processing equipment needs.

ALARD item reference #: Y5860

Tri-Clover PR25
Food Grade ROTARY LOBE PUMP
1.5 inch inlet and outlet,
with motor and base...

A Tri-Clover PR25 sanitary positive displacement rotary lobe pump with motor and base, for pumping viscous fluids, slurry and / or particulate bearing liquids in industrial food, canning, bakery & beverage processing applications.

FEATURING:

• 1.5 inch inlet and discharge ports with threaded connections in a horizontal flow orientation.
  
  
• Manufacturer rated for...
  
  
  • ...up to 28 gallons per minute,
    
    
  • 20 psi working pressure,
    
    
  • and up to 140 degrees Fahrenheit product temperature.
    
    
• Food grade sanitary stainless steel pump, with stainless steel lobes...
  
  
• ...coupled to a NEW 3HP SEW Eurodrive motor.
  
  
• Stainless steel base.
  
  
• 208 / 230 / 460 volt 3 phase electrical input.

As of this writing, this lobe pump is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition - available for immediate shipment.

CALL 315-589-4511 to confirm availability, and to discuss your particular industrial food process pump and bulk material handling needs.

ALARD item reference #: Y5833

BAG PACKING TABLE,
2-station, food grade, stainless steel,
for filling bags by weight,
with scales & bag holders...

Keep productivity and profits in clear sight with the Alard Model BT2020, 2-spout food grade stainless steel bag filler table with weigh scales and bag holders for bag-filling of precut produce by weight, such as freshcut vegetables, leafy salad mixes, florets and fresh peeled whole products. Note: single station version also available; --call 315-589-4511 to discuss your fresh produce packing needs.

FEATURES:

• This stainless steel two-person BAGGING TABLE measures 43 inches long by 75 inches wide with sides that taper from 13.75 inches high at the back down to 5.75 inches in the front.
  
  
• This bag filling manual pack table features an ANGLED BACK in order to feed product closer to the operator's reach. The flat-bottom portion of the table is only 29.5 inches in depth (from front to back), while the angled back-stop allows for additional full-load capacity.
  
  
• Two (2) 30 lb electric washdown scales with over-under remote readout display head mounted at eye level; one for each hand-packing station.
  
  
• Each bag-filling station has a standard 6.5 inch diameter filling tube, which can be fitted with an optional stainless steel filling funnel for larger or smaller bag sizes.
  
  
• Each filling tube is equipped with a stainless steel pneumatic bag holder to keep the bag held in position during the bag-filling process.
  
  
• Beneath each bag holder is a 10 inch deep (front to back) by 12 inch wide (side to side) stainless steel weigh cell platform which is height adjustable to accommodate different bag lengths.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 110 volt single phase (household current) electrical input.
  
  
• Compressed air required for the pneumatic bag holders.
  
  
• NEW.
  
  

OPERATION:

• Each operator hangs a bag on their filling funnel and engages the bag holder by pressing a button.
  
  
• The operator then pulls product from the table into the filling tube until the proper weight is made.
  
  
• Overages can easily be removed.
  
  
• The operator then disengages the bag holder and removes the bag, puts a new bag in place & the bag packing process is repeated.
  
  

This particular item was the prototype machine for this model bag filler, and as of this writing, is in stock new at Alard, fully assembled and ready-to-go, available for immediate shipment.

CALL 315-589-4511 to confirm current availability and discuss your food handling needs.

ALARD item reference #: Y5694

FOOD PROCESS METAL DETECTOR
with BELT CONVEYOR, 14x6,
food grade, stainless steel...
 

A refurbished FORTRESS BSH metal detector, on a new stainless steel thru-conveyor, with belt-stop alarm reject. A food grade belt transfer metal detection system for food processing and/or other industrial process applications.

FEATURING:

• 5 7/8 inch high by 14 inch wide USABLE aperture.
  
  
• Stainless steel detection head with new epoxy liner.
  
  
• Digital operator control panel.
  
  
• NEW stainless steel conveyor frame.
  
  
  • 11.75 inch wide by 87 inch long plastic interlocking chain belt:
    
    
  • Left to Right product flow.
    
    
  • Variable speed control.
    
    
• 34 inch working height with threaded rod adjustable feet.
  
  
• Food grade sanitary stainless steel construction
  
  
• Belt stop alarm reject, with new, integrated, gasketed PVC conveyor control box.
  
  
• 1/2 HP stainless steel shrouded washdown motor.
  
  
• 110 volt single phase (household current) electrical input.
  
  

As of writing this refurbished Fortress metal detector is in stock at ALARD, in EXCELLENT operational, mechanical, electrical & cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your industrial process metal detector needs.

ALARD item reference #: Y5724

LENGTH SLICER, ROMAINE TRIMMER, butt cutter, segment cutting machine, all stainless steel...

The F.I.R.M. Inc. Model A.R.T.T.S. is an efficient high-capacity industrial length cutter, tip & butt trimming machine, vegetable topper-tailer, length slicer, segment cutter, and/or increment cutter, for pre-cut produce / fresh-cut processing and preparation operations for food products such as romaine lettuce, celery, carrots, zucchini and other oblong shaped produce.

FEATURING:

• Sloped 18 inch long stainless steel in-feed section.
  
  
• 20 inch wide by 14 foot long cleated infeed belt with two lanes of 3.5 inch wide by 2 inch high cleats on 3 inch centers.
  
  
• 20 inch wide by 36 inch long hold down belt with adjustable counterweight.
  
  
• Eight (8) 12 inch diameter serrated blades - currently set for 1.5 inch long segments with top & butt.
  
  
• 20 inch wide by 12 foot long waste takeaway belt.
  
  
• Open frame design for ease of sanitation.
  
  
• 18 inch wide by 11 foot long operator catwalk with 33 inch working height.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 1 HP stainless steel shrouded drive motor.
  
  
• 208 / 230 / 460 volt 3 phase input.
  
  
• Previously used for making Caesar salad cuts of romaine lettuce, whereby the carrying belt was in-plant modified for that purpose. We did not elect to replace the (good usable) belt on this machine in advance of sale, since choice of flights, flight spacings, and / or other configuration aspects for this machine, would be dependent on the buyer's application requirements. Call 315-589-4511 to discuss your increment cutting, segment cutting, romaine lettuce cutting needs.
  
  
• ! NOTE ! --To be equipped with gasketed PVC operator control box with safety interlock system prior to shipment, or buyer to agree in writing to install same if purchased "as-is" for immediate shipment.

As of this writing, this length cutter is in stock at ALARD, in VERY GOOD condition, available for timely shipment.

CALL 315-589-4511 to confirm availability and discuss your particular industrial process vegetable preparation / cutting equipment needs.

ALARD item reference #: Y5288

BROWN 202 PADDLE FINISHER separator, pulper, all stainless steel...
 

This Brown International Model 202 PADDLE FINISHER, pulper, refiner, separator is manufacturer recommended for extracting juices and purees from fruits & vegetables, and separate fruit flesh (pulp) from fruit pits, seeds and/or other solids (stems, skins).

OPERATION:

• This make / model pulping / finishing machine uses spinning paddles turning inside a perforated screen. The screens are interchangeable, and the perforation size of the screen determines the "finish" of (amount of pulp in) the product.
  
  
• Liquids (juices and pulp) that pass through the screen are collected in a bottom discharge pan while the solids (pits, seeds, skins) remaining inside the screen are discharged out the end.
  
  
• Manufacturer recommended for industrial capacity food processing of apricots, pumpkin & squash, pears, apples, plums, prunes, figs, citrus juices, jam, soup, peanut butter, jelly and fruit nectar.

FEATURES:

• Manufacturer rated for input rates of up to 120 gallons per minute.
  
  
• 4 inch diameter PIPE -or- 6 inch by 12 inch hopper infeed.
  
  
• Set with .033 inch perforated screens -- other sizes available. CALL 315-589-4511 to discuss your pulper-finisher-separator needs.
  
  
• Solid paddles are individually adjustable for distance to screen.
  
  
• Stainless steel hinged side covers.
  
  
• Bottom collection pan with triclamp outlet.
  
  
• All food grade sanitary stainless steel construction.
  
  
• 20 HP belt drive motor.
  
  
• 575 volt 3 phase electrical input for Canadian voltage, transformer available for domestic US voltage.
  
  

As of this writing, this paddle finisher is in stock at ALARD, in excellent operational, mechannical, electrical, and cosmetic condition, available for immediate shipment.

CALL 315-589-4511 to confirm availability and discuss your particular pulping /finishing equipment needs.

ALARD item reference #: Y5811